High Resolution, High Accuracy Ethernet DAQ Device

DT8824 - 4-Channel Precision Measurements over Ethernet

The DT8824 offers the highest stability and accuracy for measuring analog signals. Every signal input is fully isolated from each other. This technology, ISO-Channel™, guarantees that all signals are protected from any environmental or system noise.

The high stability design of the DT8824 delivers data acquisition results that are twenty times better than the normal solution from another system.

The TCP/IP Ethernet operation allows measurements to be monitored locally or at other remote sites. Up to 16 instrument modules can be stacked for parallel operation of 64 voltage inputs. These modules are synchronized via the Wired Trigger Bus and can be externally triggered in various ways.

The DT8824 is ideally suited for chromatography, seismic, weigh scale, and medical applications where accuracy and stability are imperative. The rugged, compact module can be used as a portable device or mounted in a rack.

DT8824 - 4-Channel Precision Measurements over Ethernet

Zoom image
  • 4, simultaneous, 24-bit analog input channels
  • ISO-Channel technology provides ±500V galvanic isolation channel-to-channel for all analog input signals and to the host computer ...guarantees noise immunity
  • Input ranges per channel from ±0.3125V up to ±10V ...allows maximum flexibility for any signal input
  • Sampling rate up to 4800Hz per channel
  • 4 opto-isolated digital output lines; the outputs are solid-state relays that operate from ±30 V at currents up to 400 mA (peak) AC or DC
  • Software-programmable trigger type (software, external digital trigger, Trigger Bus, or LAN trigger) to start analog input operations
  • Synchronization reference clock, ADC sync and trigger input/output via LXI Trigger Bus for synchronizing multiple up to 16 instrument modules
  • IVI-COM instrument driver for .NET, NI LabVIEW, VEE, MATLAB (32-bit through R2015b), LabWindows/CVI development
  • Collection of Drivers, SCPI support, and manuals on CD
  • Integrated Calibration Utility
  • Use free QuickDAQ data logger application
  • Metal case, mains power supply EP361, and LAN cable included
  • dimensions: 213x237x44 mm, rack mountable, (1U by 1/2 rack)
Products Software Accessories Documents More Info Download Alternatives

High Resolution, High Accuracy Ethernet InstrumentDT8824
High Resolution, High Accuracy Ethernet Instrument

Please log in for pricing


Add for comparison
  • Input ranges per channel: ±10V, ±1.25V, ±0.625V, ±0.3125V
  • common mode voltage range ±500V

LXI Wired Trigger Bus CableEP377
LXI Wired Trigger Bus Cable
Call for pricing 

More info
  • synchronization cable
  • for use with DT8837, DT8824, or VIBbox
  • length 0.5m, other lengths available

Single Rack-Mount Kit
Please log in for pricing


More info
  • 19" mounting kit for a single instrument
  • for DT8837, DT8824, DT9824, and DT9862

Dual Rack-Mount Kit
Please log in for pricing


More info
  • 19" kit for mounting two instruments side by side
  • for DT8837, DT8824, DT9824, and DT9862

Free Data Logger Application - Upgradeable with FFT Analysis OptionsQuickDAQ
Free Data Logger Application - Upgradeable with FFT Analysis Options
Free of charge
More info

  • Two extensions add FFT analysis capabilities to the free base package.
  • QuickDAQ FFT Analysis Options allow serious sound & vibration analysis supporting modal analysis and ODS analysis methods.
  • Single-Channel and Dual-Channel (frequency response) FFT operations

Show file Datasheet
User Manuals
Show file User's Manual
Show file SCPI Manual
SCPI (Standard Commands for Programmable Instruments) is an universal programming language for electronic test and measurement instruments, based on the IEEE 488.1 and IEEE 488.2 standards. DT8824 complies with the SCPI language and implements the IEEE-488.2 STD status structure. You can issue SCPI commands over VISA or sockets.
Show file Rear Panel
Show file Web Application Oscilloscope
Show file Web Application Spectrum
Show file Web Application Info
Show file Web Application Download
Show file Web Application Calibration
Block Diagram
Show file Block Diagram
Show file Mechanical Drawing
Application Notes
Show file Using DT8824 with MATLAB
Using the Instrument Control Toolbox™ from The MathWorks™, you can access the functions of the DT8824.
Note: IVI-COM drivers are supported by MATLAB through R2015b (32-bit) only.
Show file More Information on LXI
LXI is an instrumentation platform based on industry standard Ethernet technology designed to provide modularity, flexibility and performance to small- and medium-sized systems. ..
Show file More Information on IVI
Build you own applications based on Visual C++, Visual C# and Visual Basic .NET, Visual Basic 6.0, LabVIEW, LabWindows/CVI, MATLAB, Keysight VEE Pro.
White Papers
Show file Why ISO-Channel Technology is Your Best Return on Investment
When connecting signal sources it is important to eliminate the sources of error that can contribute to inaccuracies in your measurements. In most measurement instruments, this burden is on the customer. Instruments that use ISO-Channel ...
Show file ISO-Channel™ Protection
to eliminate any common mode noise and ground loop problem in any environmental conditions
More Downloads
Show file Driver for Instrument Control Toolbox in MATLAB/Simulink
Using the Instrument Control Toolbox from The MathWorks, you can access the functions of Data Translation's instrument modules. The Instrument Control Toolbox communicates with DT instruments through a MATLAB driver to the instruments IVI-COM driver.
Software Downloads
Show file Release Notes
Show file DT8824 Support Software (253 MB)
- IVI-COM driver
- Eureka Discovery Utility
- SCPI Support (manual and examples)
- QuickDAQ 2013
These products may better fit to your requirements
DT9824 - High Resolution, High Accuracy USB Module High Accuracy Measurements with 24 Bit Resolution
DT9824 ... with USB interface

Product overview
Show file Simultaneous Data Acquisition Overview

Print PageBack To TopHelp DeskHome
Measurement Computing Corp.Phone: +49-7142-9531-0Fax: +49-7142-9531-13Email: Info@MCCdaq.de